Alpha-technologies PowerAgent SC3 Instrukcja Użytkownika Strona 25
- Strona / 57
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
PowerAgent
TM
SC3 Site Controller Document # 700-000014-01 Rev 2
Installation and Operation
Phoenix Broadband Technologies, LLC 10/28/2010
Page 25 of 57
5.9.3 SNMP Agent Configuration (3)
The SNMP Community Strings and Trap destinations are configured from the SNMP
Configuration.
The default community strings
are set to “public”. To change
the community string type “3”
followed by “Enter”. The
present read (Set) community
string will be displayed in
parenthesis as shown. To
change the community string,
type the new string followed
by “Enter”. To move to the
next item without changing
the community string just type
“Enter”. The write (Set)
community string is next and is handled the same way, followed by the Trap community string.
NOTE: Community strings are case sensitive.
Up to 3 Trap destinations can be configured. The IP addresses of the Trap destinations are set
similar to the IP address
described above. To disable
sending Traps to any of the
three IP address enter zeros
for the IP address.
The Site Controller includes a feature that will reset the device if a SNMP message is not
received for approximately 2
hours. This safety feature is
primarily used when the
device is located in a remote
unmanned location. If the
SNMP firmware hangs this
may recover the device
without a visit to the remote location. The default setting is disabled. To enable the reset type a
“Y”, to disable the feature type an “N” or “Enter”.
The menu will be redisplayed at the end of the SNMP Configuration. Select “9” to save the
changes and close the telnet session.
5.9.4 HMS Defaults (4)
To restore the factory default settings for all SNMP objects, type a “4” followed by “Enter”. The
SNMP, Email, NTP, Gateway, Net Mask, and IP Address will not be changed. The telnet session
will be closed and the Site Controller will be reset.
- Installation and Operation 1
- Table of Contents 2
- Page 3 of 57 3
- 1 Important Information 4
- 1.1 Revision History 4
- 1.2 Safety Notes 4
- 1.3 Important Symbols 5
- 1.4 Definition of Terms 5
- 1.5 Contact Information 6
- 2 System Overview 7
- 2.1 Sensor Description 8
- 2.1.2 Sensor Selector Guide 9
- Page 10 of 57 10
- Page 11 of 57 11
- 2.3 Accessories 12
- 2.3.2 Power Transformer 13
- 2.3.3 Rack Mount Bracket 13
- 3 Initial Bench Evaluation 14
- Page 15 of 57 15
- 5.1 Powering 16
- 4 Sensor Installation 16
- 5.2 Network Connections 17
- 5.6 Setting the IP Address 18
- 5.7.2 USB Port Selection 19
- 5.8.2 Router Method 20
- Page 21 of 57 21
- Page 22 of 57 22
- Page 23 of 57 23
- 5.9.2 Web Passwords (1) 24
- 5.9.4 HMS Defaults (4) 25
- 5.9.5 Email Setup (5) 26
- Page 27 of 57 27
- Page 28 of 57 28
- Page 29 of 57 29
- 5.10 Web Server 30
- 6 Navigating the Web Pages 31
- 6.1 Overview Display 32
- 6.2 Single String Display 33
- Page 34 of 57 34
- 6.3 Single Jar Display 35
- Page 36 of 57 36
- Page 37 of 57 37
- 6.5 Provisioning 38
- Page 39 of 57 39
- Page 40 of 57 40
- Page 41 of 57 41
- Page 42 of 57 42
- Page 43 of 57 43
- Page 44 of 57 44
- Page 45 of 57 45
- Page 46 of 57 46
- 6.5.4.6 Setting a Baseline 47
- Page 48 of 57 48
- Page 49 of 57 49
- Page 50 of 57 50
- 6.5.7 Provisioning The ROM 51
- 7 SNMP 52
- 7.1.1 MIBs 53
- 7.1.2 Community Strings 54
- 7.1.3 Traps 54
- 7.1.4 MIB Browsers 54
- 8 Updating Firmware 55
- 9 Summary of Port Usage 56
- Page 57 of 57 57
Powiązane produkty i podręczniki dla Oprogramowanie Alpha-technologies PowerAgent SC3
(2 strony)AEG T8DB84GW manuels
Manuels d'utilisation et guides de l'utilisateur pour Non AEG T8DB84GW.
Nous fournissons des manuels en pdf 3 AEG T8DB84GW à télécharger gratuitement par type de document : Manuel de l'utilisateur
Komentarze do niniejszej Instrukcji